Furnace Repair in Edwards, Colorado Done Right

When your heat quits in Edwards, you need a furnace repair team that knows mountain weather and shows up ready to work. We diagnose gas and electric furnaces, replace failed igniters and blower motors, and get your system running the same day. Our technicians carry the tools and parts to fix most brands on the first visit, so you are not waiting overnight in a cold house.

Call Now Book Online

Emergency response Average repair time Customer rating

Licensed Licensed & Bonded

Fully Insured Insured & Bonded

24/7 Emergency Same-Day Response

Warranty Backed Workmanship Guaranteed in Edwards

Your Local Furnace Repair in Edwards

Furnace Repair in Edwards is a category of heating service that restores heat to homes and businesses when a furnace stops working, runs inefficiently, or fails a safety check. We work on every major brand, from Lennox and Carrier to Trane, Goodman, and Rheem, and we stock the parts that fail most in mountain homes. Edwards sits at 7,200 feet, where winter nights drop below zero and furnaces run hard from October through April. That kind of workload wears out flame sensors, igniters, and blower motors faster than in lower elevations. We serve homeowners in Arrowhead, Singletree, and the Berry Creek area, plus the condo and lodge properties along the Eagle River. Whether you need a quick tune-up before the season or an emergency repair on a Sunday night, we have the tools and the local experience to get it done.

Locally licensed and insured in Edwards
Same-day diagnostics and written estimates
Real workmanship warranty in writing
Background-checked, in-house technicians

Furnace Repair Services Available in Edwards

Edwards homeowners call us for everything from a furnace blowing cold air to a full system replacement. We handle gas and electric furnaces, high-efficiency models, and older units that need a skilled hand. If you are searching for a furnace repair near me in Edwards, we are the local team that answers the phone and shows up. Our trucks carry the tools and parts to fix most problems on the first visit.

Furnace Repair

We fix furnaces that won't ignite, blow cold air, or short cycle. In Edwards, we see a lot of dirty flame sensors and failed igniters from heavy winter use. Our technicians test the gas valve, blower motor, and control board, then make the repair on the spot. Most jobs take two to four hours.

View Details

Furnace Installation

New furnace installation in Edwards means sizing the unit for 7,200 feet of altitude and a long heating season. We handle permits, venting, and gas line connections. Whether you are building in Singletree or replacing an old unit in Arrowhead, we install it right and test every safety control before we leave.

View Details

Furnace Replacement

When your furnace is past its prime, we replace it with a high-efficiency model that handles Edwards winters. We haul away the old unit, update the venting if needed, and make sure the new system matches your ductwork. Most replacements are done in one day, and we walk you through the new thermostat before we go.

View Details

Furnace Tune-Up

A fall tune-up in Edwards is the best way to avoid a mid-winter breakdown. We clean the flame sensor, check the igniter, test the gas valve, and measure airflow. We also inspect the heat exchanger for cracks. It takes about an hour, and it can catch small problems before they leave you without heat.

View Details

Furnace Maintenance

Our maintenance plan keeps Edwards furnaces running efficiently all season. We change filters, check the blower motor capacitor, and clean the burners. For second homes and rentals, we schedule visits around occupancy so you are not left with a cold unit during a guest stay. Regular maintenance also protects your manufacturer warranty.

View Details

Emergency Furnace Repair

When your furnace dies at 2 a.m. in Edwards, we answer the phone. Our emergency team handles no-heat calls, gas smells, and furnaces tripping breakers. We prioritize homes with elderly residents, young children, or frozen pipe risk. Response times in the Edwards area are typically under 90 minutes for true emergencies.

View Details

Gas Furnace Repair

Gas furnace repair in Edwards requires a technician who knows combustion. We use a combustion analyzer to check for carbon monoxide and proper flame. We repair gas valves, thermocouples, and pilot assemblies. If we find a cracked heat exchanger, we tell you straight and give you options for repair or replacement.

View Details

Electric Furnace Repair

Electric furnaces in Edwards often fail at the heating element or sequencer. We use a clamp meter and multimeter to trace the problem. We repair or replace failed components and check the blower motor for wear. Most electric furnace repairs are straightforward, and we carry common parts on our trucks.

View Details

High-Efficiency Furnace Repair

High-efficiency furnaces in Edwards need a tech who understands condensing technology. We diagnose issues with the secondary heat exchanger, condensate lines, and variable-speed blower motors. These systems save money on fuel, but they need precise repair. We use manufacturer-specific diagnostics to get it right the first time.

View Details

Furnace Cleaning

Dust and debris build up fast in Edwards homes, especially during construction or wildfire smoke season. Our furnace cleaning service includes burner cleaning, flame sensor cleaning, and blower compartment vacuuming. We also check the air filter and duct connections. A clean furnace runs cooler, uses less gas, and lasts longer.

View Details

Service · #1

Furnace Repair in Edwards

When your furnace quits in Edwards, Colorado, you need furnace repair in Edwards fast. Our technicians know the mountain climate and the older homes in Edwards Village and Berry Creek. We diagnose no-heat calls, strange noises, and short cycling, then fix them right the first time. From Singletree to Cordillera, we keep Edwards families warm all winter.

Common Furnace Problems

Edwards homes often face ignitor failures, dirty flame sensors, and cracked heat exchangers due to altitude and temperature swings. We troubleshoot these furnace repair issues daily in neighborhoods like Homestead and Arrowhead. Our trucks carry common parts, so most repairs finish in one visit. We also check for carbon monoxide risks before leaving.

Fast Response Times

We prioritize furnace repair in Edwards because cold snaps hit hard at 7,000 feet. Our dispatch covers Edwards Village, Singletree, and Cordillera with same-day appointments. When your heat fails on a Sunday, we answer. We arrive with diagnostic tools and a clear estimate before any work begins.

Repairs for Older Systems

Many Edwards homes built in the 1980s and 1990s have furnaces nearing end of life. We repair aging units when safe, replacing blower motors, control boards, and inducer assemblies. If a fix is not cost-effective, we explain replacement options honestly. Our goal is reliable heat for another season.

Same-day furnace repair for Edwards Village and Singletree homes
Diagnose no-heat, short cycling, and strange furnace noises
Replace ignitors, flame sensors, blower motors, and control boards
Test carbon monoxide levels and verify safe furnace operation

Furnace Installation in Edwards

Furnace installation in Edwards requires a contractor who understands mountain altitude and tight building envelopes. We size and install furnaces for homes in Cordillera, Arrowhead, and the Reserve. Our team handles permits, gas line checks, and ductwork adjustments. You get a warm, efficient system built for Edwards winters, not a one-size-fits-all box.

01

Proper Sizing for Altitude

At 7,000 feet, furnaces lose efficiency and require altitude-specific adjustments. We perform a Manual J load calculation for every Edwards home, whether in Singletree or Edwards Village. Oversized units short cycle and waste gas. We match BTU output to your square footage, insulation, and window exposure for optimal comfort.
02

New Construction Installs

Edwards sees new builds in Miller Ranch and Berry Creek, and we partner with builders for furnace installation. We coordinate with HVAC rough-in schedules, run new gas lines, and seal ductwork before drywall. Our installs meet Colorado code and pass inspection. We also register warranties and walk you through thermostat setup.
03

Replacement Install Process

When replacing an old furnace in Edwards, we remove the unit, inspect the heat exchanger, and check duct static pressure. We install a new furnace, reconnect gas and electrical, and test combustion. Most jobs finish in one day. We haul away the old equipment and leave your mechanical room clean.

Manual J load calculations for Edwards mountain homes
Install high-efficiency furnaces in Cordillera and Arrowhead
Coordinate gas line, ductwork, and permit inspections
Remove old furnace and register new warranty

02 / 10

Service

5+ YEARS · EDWARDS

Furnace Replacement in Edwards

Furnace replacement in Edwards is a big decision, and we make it straightforward. If your furnace is over 15 years old or needs frequent repairs, replacement often saves money. We serve Edwards Village, Homestead, and Cordillera with honest assessments. Our team helps you choose a system that fits your home and budget.

Signs You Need Replacement

Rising gas bills, yellow flames, and repeated breakdowns signal it is time for furnace replacement in Edwards. Homes in Berry Creek and Singletree with original 1990s furnaces often hit this point. We inspect your heat exchanger for cracks and check efficiency ratings. If repairs exceed half the cost of new, we recommend replacing.

Choosing a New Furnace

We guide Edwards homeowners through AFUE ratings, variable-speed blowers, and two-stage heating. For cold mountain nights, a 96% AFUE furnace with sealed combustion works best. We compare brands like Carrier, Trane, and Lennox. You get options for budget, noise level, and warranty length before you commit.

Removal and Disposal

Our furnace replacement in Edwards includes full removal of the old unit, refrigerant lines if applicable, and proper disposal. We recycle metal and dispose of hazardous components legally. We also inspect and seal duct connections to improve airflow. The new furnace is tested and calibrated before we leave.

Assess old furnace and recommend replacement vs repair
Offer 96% AFUE and variable-speed furnace options
Remove and recycle old equipment safely
Test new furnace and seal duct connections

Furnace Tune-Up in Edwards

A furnace tune-up in Edwards before winter prevents mid-season breakdowns. Our technicians clean burners, check gas pressure, and test safety controls. We serve Edwards Village, Singletree, and Arrowhead with thorough seasonal maintenance. Regular tune-ups keep your warranty valid and your heating bills lower. Book yours before the first snow flies.

Clean burners and inspect flame sensor

Promise

“Our furnace tune-up in Edwards covers burner cleaning, flame sensor inspection, and heat exchanger checks. We measure amp draw on blower motors and test ignitors. We also verify venting and carbon monoxide levels. For…”

— Edwards customer

What a Tune-Up Includes +

Our furnace tune-up in Edwards covers burner cleaning, flame sensor inspection, and heat exchanger checks. We measure amp draw on blower motors and test ignitors. We also verify venting and carbon monoxide levels. For homes in Cordillera and Berry Creek, we adjust for altitude to maintain efficiency.

Why Fall Tune-Ups Matter +

Edwards winters arrive fast, and a furnace that sat idle all summer can fail on the first cold night. A fall tune-up catches worn belts, dirty filters, and loose electrical connections. We also clear debris from intake and exhaust pipes. This service extends equipment life and prevents emergency calls.

Tune-Up vs Maintenance +

A tune-up is a seasonal check, while furnace maintenance in Edwards is a broader annual plan. Tune-ups focus on cleaning and adjusting for peak performance. Maintenance adds part lubrication, filter changes, and a full system audit. We offer both, and we recommend at least one tune-up per year.

Clean burners and inspect flame sensor
Test ignitor, gas pressure, and safety controls
Check heat exchanger for cracks and corrosion
Verify venting and carbon monoxide levels

Service · #5

Furnace Maintenance in Edwards

Furnace maintenance in Edwards keeps your system running safely and efficiently all winter. Our maintenance plans include annual inspections, filter changes, and priority scheduling. We work in Edwards Village, Homestead, and Cordillera. Regular maintenance prevents costly breakdowns and extends furnace life. Join our plan and stop worrying about surprise failures.

Annual Maintenance Plan

Our Edwards furnace maintenance plan includes two visits per year: a fall tune-up and a spring check. We clean components, test safety switches, and replace standard filters. Plan members get priority scheduling and discounts on repairs. It is the easiest way to protect your heating investment.

Filter and Airflow Care

Dirty filters strain furnaces in Edwards homes, especially during dusty spring months. We replace filters with high-quality pleated options and check duct static pressure. Poor airflow causes overheating and short cycling. Our maintenance visits ensure your system breathes easy and heats evenly.

Safety Inspections

Every furnace maintenance visit in Edwards includes a carbon monoxide test and heat exchanger inspection. We check gas connections for leaks and verify proper venting. In older homes near Berry Creek, we look for rust and corrosion. Safety is our top priority before comfort.

Two annual visits: fall tune-up and spring check
Replace filters and measure duct static pressure
Test carbon monoxide and inspect heat exchanger
Priority scheduling and repair discounts for members

Emergency Furnace Repair in Edwards

When your furnace dies at 2 a.m. in Edwards, you need emergency furnace repair now. Our on-call technicians serve Edwards Village, Singletree, and Cordillera around the clock. We diagnose no-heat calls, gas smells, and electrical failures fast. Do not wait until morning-call us for immediate help.

01

24/7 Emergency Availability

We answer emergency furnace repair calls in Edwards 24 hours a day, including weekends and holidays. Our dispatch sends the nearest technician with a fully stocked truck. We troubleshoot ignitors, blower motors, and control boards on site. Most emergency calls are resolved in one visit.
02

What Counts as Emergency

No heat in freezing temperatures, gas odors, or carbon monoxide alarms are true emergencies in Edwards. We also treat repeated breaker trips and loud banging noises as urgent. If your furnace smells like burning plastic, shut it off and call us. We prioritize safety and rapid response.
03

Preventing Future Emergencies

After emergency furnace repair in Edwards, we recommend a maintenance plan to avoid repeat failures. We inspect the entire system, replace worn parts, and clean burners. For homes in Arrowhead and Homestead, we also check altitude-related issues. A little prevention goes a long way.

24/7 emergency dispatch for Edwards and surrounding areas
Same-night repair for no-heat and gas smell calls
Stocked trucks with ignitors, blowers, and control boards
Post-repair safety check and maintenance recommendations

06 / 10

Service

5+ YEARS · EDWARDS

Gas Furnace Repair in Edwards

Gas furnace repair in Edwards requires a technician who respects the risks of natural gas and propane. We diagnose pilot issues, gas valve failures, and ignition problems. Our team serves Edwards Village, Cordillera, and Singletree. We test for leaks, verify combustion, and restore safe heat quickly. Call us for expert gas furnace service.

Common Gas Furnace Issues

Edwards gas furnaces often suffer from dirty pilot assemblies, faulty thermocouples, and clogged burners. At high altitude, gas pressure can drift, causing weak flames. We adjust manifold pressure and clean orifices. We also check for cracked heat exchangers that leak carbon monoxide into your home.

Gas Leak Safety

If you smell gas in your Edwards home, leave immediately and call 911, then call us for gas furnace repair. We use electronic leak detectors to find faulty valves, loose fittings, or cracked pipes. We repair or replace components and pressure-test the system. Never ignore a gas smell.

Propane Systems in Edwards

Many rural Edwards properties use propane furnaces. Propane burns differently than natural gas, requiring specific orifices and pressure settings. We repair propane furnaces in Arrowhead and Berry Creek, converting or tuning them for altitude. Our techs carry propane-specific parts and test instruments.

Diagnose pilot, ignition, and gas valve failures
Electronic gas leak detection and pressure testing
Adjust manifold pressure for Edwards altitude
Repair propane and natural gas furnaces

Electric Furnace Repair in Edwards

Electric furnace repair in Edwards is our specialty for homes without gas lines. We fix heating elements, sequencers, and blower motors. Our technicians serve Edwards Village, Miller Ranch, and Homestead. We diagnose tripped breakers, no-heat calls, and strange noises. Trust us to restore safe, efficient electric heat.

Test and replace failed heating elements

Promise

“Electric furnaces in Edwards rely on heating elements that can burn out over time. We test each element for continuity and replace failed ones. If your furnace blows cold air, a broken element is likely. We also check…”

— Edwards customer

Heating Element Failures +

Electric furnaces in Edwards rely on heating elements that can burn out over time. We test each element for continuity and replace failed ones. If your furnace blows cold air, a broken element is likely. We also check sequencers and limit switches to prevent short cycling.

Electrical Safety Checks +

Before any electric furnace repair in Edwards, we inspect wiring, breakers, and disconnects for signs of overheating. Loose connections cause voltage drops and fire risks. We tighten terminals and replace damaged wire. We also verify proper grounding and GFCI protection where required.

Blower and Airflow Issues +

A failing blower motor leaves Edwards homes without heat distribution. We diagnose capacitor failures, worn bearings, and dirty blower wheels. We clean or replace components to restore airflow. For homes in Cordillera, we also balance registers to improve comfort.

Test and replace failed heating elements
Inspect breakers, wiring, and disconnects for safety
Repair or replace blower motors and capacitors
Balance airflow and verify limit switch operation

Service · #9

High-Efficiency Furnace Repair in Edwards

High-efficiency furnace repair in Edwards demands technicians who understand condensing technology. We fix PVC venting issues, condensate drains, and variable-speed blowers. Our team serves Edwards Village, Singletree, and Cordillera. These systems save energy but need precise repairs. Call us to keep your high-efficiency furnace running at peak performance.

Condensate Drain Problems

High-efficiency furnaces in Edwards produce acidic condensate that can clog drains and freeze in winter. We clear blockages, repair leaks, and install heat tape on exposed pipes. A blocked drain shuts down the furnace. We also check neutralizer kits to protect your plumbing.

PVC Venting Repairs

Unlike older furnaces, high-efficiency models vent through PVC pipes. In Edwards, these pipes can sag, crack, or collect debris. We inspect vent slope, joints, and termination points. Improper venting causes carbon monoxide buildup. We repair or replace venting to meet code.

Variable-Speed Blower Issues

Variable-speed blowers in high-efficiency furnaces require specialized diagnostics. We troubleshoot control boards, ECM motors, and static pressure problems. For Edwards homes in Berry Creek, we adjust airflow for altitude. A faulty blower reduces efficiency and comfort. We restore smooth, quiet operation.

Clear condensate drains and install heat tape
Repair PVC venting and verify proper slope
Diagnose variable-speed blower and ECM motors
Test combustion and adjust for altitude efficiency

Furnace Cleaning in Edwards

Furnace cleaning in Edwards removes dust, soot, and debris that reduce efficiency and air quality. Our technicians clean burners, blower wheels, and heat exchangers. We serve Edwards Village, Homestead, and Arrowhead. A clean furnace runs cooler, lasts longer, and keeps your family healthier. Schedule your cleaning before winter.

01

Deep Cleaning Process

Our furnace cleaning in Edwards starts with a full inspection, then we brush and vacuum burners, flame sensors, and blower compartments. We use HEPA vacuums to capture fine dust. For homes in Cordillera, we also clean intake screens and vent pipes. The result is better airflow and cleaner heat.
02

Improving Indoor Air Quality

Dirty furnaces circulate dust, pollen, and mold spores through Edwards homes. Our cleaning service removes built-up debris from the heat exchanger and blower. We also recommend high-MERV filters for allergy sufferers. Cleaner furnaces mean fewer respiratory issues and a fresher home environment.
03

When to Schedule Cleaning

We recommend furnace cleaning in Edwards once a year, ideally in early fall. If you see soot around registers or smell burning dust, schedule sooner. Homes with pets or recent remodeling need more frequent cleaning. We offer flexible appointments in Singletree and Miller Ranch.

Brush and vacuum burners, blower, and heat exchanger
Use HEPA vacuums to capture fine dust and debris
Clean intake screens and vent pipes for airflow
Recommend high-MERV filters for better air quality

10 / 10

Service

Residential Furnace Repair in Edwards

Edwards homes range from condos to large mountain houses, and each has different heating needs. We work with homeowners to keep their families warm and their energy bills down. Whether you need a quick repair or a new system, we are here to help.

Emergency no-heat repair — When your furnace quits in the middle of a cold Edwards night, we respond fast. We diagnose the problem and fix it on the spot whenever possible. We carry common parts like igniters and flame sensors.
Furnace tune-ups and maintenance — Regular maintenance is key to avoiding breakdowns. We clean and inspect your furnace, check for safety issues, and replace worn parts. Our Edwards customers who maintain their furnaces have fewer emergencies.
High-efficiency furnace installation — If your old furnace is costing you too much, we can install a high-efficiency model. We size it for your home and altitude, and we handle all the permits. You'll save money on gas and stay warmer.
Smart thermostat installation — We install and configure smart thermostats like Nest and Honeywell. These let you control your heat from your phone, which is great for second homes. We can set up alerts for temperature drops.

Commercial Furnace Repair in Edwards

Edwards businesses need reliable heat to keep customers and employees comfortable. We service commercial furnaces in offices, retail spaces, and restaurants. We understand that downtime costs you money, so we work fast and schedule around your hours.

RestaurantsRetail storesOffice buildingsProperty managementHotels and lodges

Common Furnace Problems in Edwards

Edwards furnaces face unique challenges: high altitude, extreme cold, and a mix of old and new homes. These factors lead to specific problems we see again and again.

Dirty flame sensor causing no heat

At high altitude, furnaces produce more soot and debris. The flame sensor gets coated and can't detect the flame, so the furnace shuts down. This is very common in Edwards.

Cracked heat exchanger from altitude stress

The constant expansion and contraction from heating cycles, combined with altitude, stresses the heat exchanger. Cracks can leak carbon monoxide into your home.

Blower motor failure due to long run times

Edwards winters are long, so blower motors run for months on end. The bearings wear out and the motor fails. This leaves you with no airflow.

Furnace leaking water from condensation

High-efficiency furnaces produce condensate. In Edwards, the drain line can freeze if it runs outside or through a cold space. This causes water to back up and leak.

Signs You Need Furnace Repair in Edwards

Your furnace usually gives you warning signs before it quits. In Edwards, where winters are long and cold, catching these early can save you from a freezing night. Here are the top signs it's time to call for furnace repair.

Furnace blowing cold air

If your vents are blowing cold air, the furnace may have a failed igniter, a dirty flame sensor, or a gas valve issue. This is one of the most common calls we get in Edwards. It needs immediate attention.
Furnace not igniting

You hear the furnace click but it doesn't fire up. This often points to a faulty igniter or thermocouple. Without ignition, you get no heat. We can test and replace these parts quickly.
Furnace making banging noise

A banging or booming sound usually means delayed ignition. Gas is building up and then igniting suddenly. This can damage the heat exchanger and is a safety concern. Call us right away.
Furnace tripping breaker

If your furnace keeps tripping the breaker, it could be a shorted blower motor, a bad capacitor, or a wiring issue. This is an electrical problem that needs a professional. Don't keep resetting the breaker.
Furnace short cycling

Short cycling means the furnace turns on and off frequently without heating the house. It can be caused by an oversized furnace, a clogged filter, or a thermostat problem. It wears out the system and raises your bills.

Furnace Repair Pricing in Edwards

Furnace repair in Edwards typically costs between $180 and $450 for common fixes like igniters, flame sensors, and blower motors. More complex repairs, such as a heat exchanger replacement or control board swap, can run $600 to $1,200. In 2026, these prices reflect the cost of parts and the specialized tools we use at altitude. We charge a standard diagnostic fee that we waive if you proceed with the repair. We always give you a written estimate before we start work. No surprises.

Basic Service

$89 starting · per visit

Diagnostic visit
Written estimate
Same-day scheduling
30-day warranty

Book This Plan

Landmarks and Points of Interest in Edwards

We use local landmarks to navigate Edwards and reach you faster. Whether you are near the Riverwalk or out by the college, we know the shortcuts and the parking situations. Here are a few spots we use for orientation.

Edwards Riverwalk

The Riverwalk is a central gathering spot with shops and restaurants. We use it as a reference point for calls in the surrounding condos and businesses.

Colorado Mountain College Edwards

The CMC campus is a well-known landmark on the north side of Edwards. It helps us locate nearby residential streets and rental properties.

The Club at Cordillera

Cordillera is a large community south of Edwards. We use the club entrance as a waypoint for navigating to homes in the surrounding area.

Coverage across Edwards & Eagle County

81632

Plus surrounding Eagle County neighborhoods, with same-day routing on most appointments.

Seasonal Furnace Repair Considerations in Edwards

Edwards has four distinct seasons, and each one affects your furnace differently. Here's what to expect and how to prepare.

Spring

Spring in Edwards is still cold, and furnaces continue to run. We see issues from winter wear, like dirty filters and worn blower motors. It's a good time to schedule a tune-up.

Tip: Change your filter and schedule a spring tune-up to catch problems before summer.

Summer

Summer is mild, but it's the best time to replace an old furnace or schedule maintenance. We are less busy, so you get faster scheduling. We also offer AC service if you have it.

Tip: Book your furnace replacement or maintenance in summer for the best availability.

Fall

Fall is when we get the most tune-up calls. Everyone wants their furnace ready for winter. We also see issues from systems that sat unused all summer, like pilot lights out and nests in the venting.

Tip: Schedule your fall tune-up early. Don't wait until the first cold snap.

Winter

Winter is our busiest season. Furnaces run constantly, and emergency calls spike during cold snaps. We prioritize no-heat calls and safety issues like gas smells.

Tip: Keep your filter clean and watch for signs of trouble. If your furnace quits, call us immediately.

Nearby Cities We Serve from Edwards

We cover Edwards and the surrounding Eagle County communities. If you are in one of these nearby towns, we can get to you just as fast. Our service area includes the entire valley.

(City)

Agate

Agate is a small community east of Edwards. We serve homeowners there who need furnace repair and maintenance.

View Agate

(City)

Allenspark

Allenspark is northeast of Edwards, up in the mountains. We make the drive for emergency furnace repairs in this area.

View Allenspark

(City)

Antonito

Antonito is in the San Luis Valley, south of Edwards. We provide furnace service for customers in this rural area.

View Antonito

(City)

Arboles

Arboles is southwest of Edwards near Navajo Lake. We serve second homes and full-time residents in this area.

View Arboles

(City)

Arvada

Arvada is a Denver suburb, east of Edwards. We have technicians who cover the Front Range for furnace repair.

View Arvada

(City)

Aspen

Aspen is south of Edwards over Independence Pass. We provide furnace repair and installation for homes in the Aspen area.

View Aspen

Furnace Repair in Edwards: FAQs

Real answers from our team for the questions we hear most often before a job starts.

Talk to a real pro: (833) 588-3896

How much does furnace repair cost in Edwards?

Most furnace repairs in Edwards cost between $180 and $450, depending on the part and labor. Common fixes like flame sensors and igniters are on the lower end. More complex repairs like heat exchangers can run $600 to $1,200. We give you a written estimate before we start.

How fast can you get to my house in Edwards for an emergency?

We typically reach emergency calls in Edwards within 60 to 90 minutes. If you are in a remote part of the valley, it may take a bit longer. We prioritize no-heat calls and safety issues. Call us anytime, day or night.

Do you repair high-efficiency furnaces in Edwards?

Yes, we repair all types of high-efficiency furnaces, including condensing models from Lennox, Carrier, and Trane. These systems require special tools and knowledge, especially at altitude. Our techs are trained on the latest high-efficiency technology.

What should I do if my furnace is blowing cold air?

First, check your thermostat to make sure it's set to heat. Then check the air filter and replace it if it's dirty. If that doesn't fix it, call us. Cold air often means a failed igniter or flame sensor. We can diagnose and repair it quickly.

Do you offer maintenance plans for Edwards homeowners?

Yes, we offer annual maintenance plans that include a fall tune-up and priority service. For second homes and rentals, we can schedule visits around occupancy. Regular maintenance prevents breakdowns and extends the life of your furnace.

Get Furnace Repair in Edwards Today

Don't wait until your pipes freeze. If your furnace is acting up, call us now. We offer same-day service and 24/7 emergency response in Edwards. Our licensed techs will diagnose the problem and give you a straight answer. Call (833) 588-3896 or book online.

Call Now Send a Message

Get In Touch With Us

Call (833) 588-3896 any time, day or night. A live dispatcher answers, asks what your furnace is doing, and gives you a real arrival window. For non-emergency tune-ups and installs, email us and we'll get back to you the same business day.

Call (833) 588-3896

Furnace Pros Colorado

Phone
(833) 588-3896
Address

Colorado
Hours

Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available